Calculate Forum

How to get work of cardreader

What should ?

Edit kernel configuration

Installing the Drivers

The USB driver serves up your reader as a SCSI device, so you also need to install the SCSI drivers. In the “SCSI Support” section, enable these. The configuration name and the module name are listed:

SCSI Support (CONFIG_SCSI, scsi.o)
SCSI disk support (CONFIG_BLK_DEV_SD, sd_mod.o)
SCSI generic support (CONFIG_CHR_DEV_SG, sg.o)

Probe all LUNs on each SCSI device (CONFIG_SCSI_MULTI_LUN), required only for multi-card devices.
You need to use the USB mass storage driver to access your reader. In the “USB Support” section of the kernel configuration, enable the following:

Support for USB (CONFIG_USB, usb.o)
Preliminary USB device file system (CONFIG_USB_DEVICEFS)
Whatever USB drivers you need, one or more of: ECHI HCD (CONFIG_USB_EHCI_HCD, usb-ehci-hcd.o), UHCI (CONFIG_USB_UHCI, usb-uhci.o), OHCI (CONFIG_USB_OHCI, usb-ohci.o)
USB Mass Storage support (CONFIG_USB_STORAGE, usb-storage.o)

Make sure you do not select the “Low Performance USB Block Driver” (BLK_DEV_UB). It will prevent the whole thing from working correctly.

Compile your kernel with these options and reboot (or just load the relevant modules if you’ve got them). And, plug the thing in, if you haven’t already.

Multi Card Readers

If you have an n-in-1 card reader that can deal with multiple cards, the process isn’t much different. Make sure that “Probe all LUNs on each SCSI device” (CONFIG_SCSI_MULTI_LUN) is enabled in your kernel. If this isn’t compiled in, you can add this line to your /etc/modprobe.d/cardreader:

options scsi_mod max_scsi_luns=8

Or, for a more temporary solution, run this command:

echo 8 > /sys/module/scsi_mod/parameters/max_luns

**_

When that is done you must reboot, and use new kernel.
And type 'sg_scan -i' for scan SCSI devices.

Should get text like that:

[8016:8012 0:510] 10:28:03 вт ное 02 [root@Calculate64: +2] ~ 
(2:510)# sg_scan -i
/dev/sg0: scsi0 channel=0 id=0 lun=0 [em]
    ATA       ExcelStor Techno  P22O [rmb=0 cmdq=0 pqual=0 pdev=0x0] 
/dev/sg1: scsi1 channel=0 id=0 lun=0 [em]
    ATA       ST3160815AS       3.AA [rmb=0 cmdq=0 pqual=0 pdev=0x0] 
/dev/sg2: scsi4 channel=0 id=0 lun=0 [em]
    HL-DT-ST  DVDRAM GSA-H44N   RB00 [rmb=1 cmdq=0 pqual=0 pdev=0x5] 
/dev/sg3: scsi4 channel=0 id=1 lun=0 [em]
    HL-DT-ST  DVD-RAM GSA-H58N  1.01 [rmb=1 cmdq=0 pqual=0 pdev=0x5] 
/dev/sg4: scsi6 channel=0 id=0 lun=0 [em]
    Generic   USB Storage-CFC   I19A [rmb=1 cmdq=0 pqual=0 pdev=0x0] 
/dev/sg5: scsi6 channel=0 id=0 lun=1 [em]
    Generic   USB Storage-SDC   I19A [rmb=1 cmdq=0 pqual=0 pdev=0x0] 
/dev/sg6: scsi6 channel=0 id=0 lun=2 [em]
    Generic   USB Storage-SMC   I19A [rmb=1 cmdq=0 pqual=0 pdev=0x0] 
/dev/sg7: scsi6 channel=0 id=0 lun=3 [em]
    Generic   USB Storage-MSC   I19A [rmb=1 cmdq=0 pqual=0 pdev=0x0] 
699/3017MB  0.98 1.05 1.33 1/291 14282
[8016:8012 0:511] 10:28:14 вт ное 02 [root@Calculate64: +2] ~ 
(2:511)#
Mastodon Mastodon